Mparadis at 14:26, 9 May 2018

2018-05-09T14:26:00Z

← Older revision		Revision as of 14:26, 9 May 2018
Line 1:		Line 1:
			__NOINDEX__
	[[Category:UserGuide]]		[[Category:UserGuide]]
	{{UserguideTOC\|1010.jpg\|1010}}		{{UserguideTOC\|1010.jpg\|1010}}

Mparadis: /* Product History */

2016-04-19T19:00:26Z

Product History

← Older revision		Revision as of 19:00, 19 April 2016
Line 102:		Line 102:
	{{UGhist}}		{{UGhist}}
	{{UGrow\|April 2011\|0\|903\|Product Release}}		{{UGrow\|April 2011\|0\|903\|Product Release}}
	{{UGrow\|May 2011 \|0\|904\|~~getLabel~~ fix}}		{{UGrow\|May 2011 \|0\|904\|getLabelString fix for lables > 7 characters}}

Mparadis: /* Product History */

2016-04-19T18:58:59Z

Product History

← Older revision		Revision as of 18:58, 19 April 2016
Line 101:		Line 101:
	==Product History==		==Product History==
	{{UGhist}}		{{UGhist}}
	{{UGrow\|April 2011\|0\|~~902~~\|Product Release}}		{{UGrow\|April 2011\|0\|903\|Product Release}}
			{{UGrow\|May 2011 \|0\|904\|getLabel fix}}

Burley: /* Getting Started */

2013-05-09T17:23:59Z

Getting Started

← Older revision		Revision as of 17:23, 9 May 2013
Line 10:		Line 10:

	[[File:1010_0_Connecting_The_Hardware.jpg\|300px\|link=]]		[[File:1010_0_Connecting_The_Hardware.jpg\|300px\|link=]]

			The schematic for this board is available here:

			[http://www.phidgets.com/wiki/images/4/46/1010_EUE_P1_0.pdf]

	==Technical Details==		==Technical Details==

Mparadis: /* Technical Details */

2012-10-16T16:32:51Z

Technical Details

← Older revision		Revision as of 16:32, 16 October 2012
Line 18:		Line 18:

	'''GND''' is the USB Ground - all ground pins are connected together internally.		'''GND''' is the USB Ground - all ground pins are connected together internally.

			'''D+''' and '''D-''' are the differential USB data lines.

	'''IN0 - IN7''' are digital inputs. For more information, see the [[Digital Input Primer]].		'''IN0 - IN7''' are digital inputs. For more information, see the [[Digital Input Primer]].

Mparadis: /* API */

2012-08-21T15:27:46Z

API

← Older revision		Revision as of 15:27, 21 August 2012
Line 31:		Line 31:

	===Functions===		===Functions===
	~~{{UGapi\|a\|a}}~~

	{{UGapi\|int InputCount() [get] : Constant <nowiki>=</nowiki> 8		{{UGapi\|int InputCount() [get] : Constant <nowiki>=</nowiki> 8
	\|Returns the number of digital inputs supported by this PhidgetInterfaceKit.		\|Returns the number of digital inputs supported by this PhidgetInterfaceKit.

Burley at 15:07, 10 August 2012

2012-08-10T15:07:24Z

← Older revision		Revision as of 15:07, 10 August 2012
Line 1:		Line 1:
	[[Category:UserGuide]]		[[Category:UserGuide]]
			{{UserguideTOC\|1010.jpg\|1010}}
	==Getting Started==		==Getting Started==

Mparadis at 15:38, 26 July 2012

2012-07-26T15:38:30Z

← Older revision		Revision as of 15:38, 26 July 2012
Line 1:		Line 1:
			[[Category:UserGuide]]

	==Getting Started==		==Getting Started==

Mparadis: Created page with "==Getting Started== In order to use the 1010, you must be comfortable with designing your own circuit. You will need to understand the “signals” coming from and going to..."

2012-07-19T19:23:48Z

Created page with "==Getting Started== In order to use the 1010, you must be comfortable with designing your own circuit. You will need to understand the “signals” coming from and going to..."

New page

==Getting Started==

In order to use the 1010, you must be comfortable with designing your own circuit. You will need to understand the “signals” coming from and going to the 1010.

If you are not familiar with Phidgets, we recommend purchasing a [[1018 User Guide|1018]] to familiarize yourself with Phidget concepts before attempting to design the 1010 into your system.

Here is an example of a small board we have built for internal testing purposes. We have some LEDs, 2 relays, a power jack, and a couple of connectors.

[[File:1010_0_Connecting_The_Hardware.jpg|300px|link=]]

==Technical Details==

[[File:1010_0_PinOut.jpg|300px|link=]]

'''5V''' is the USB Power Supply - made available to your application if it requires a small amount of current (<400mA). All 5V pins are connected together internally.

'''GND''' is the USB Ground - all ground pins are connected together internally.

'''IN0 - IN7''' are digital inputs. For more information, see the [[Digital Input Primer]].

'''OUT0 - OUT7''' are digital outputs. For more information, see the [[Digital Output Primer]].

'''AIN0 - AIN7''' are analog inputs. For more information, see the [[Analog Input Primer]].

For dimensions, please refer to the Mechanical Drawing on the Product Page.

==API==
{{UGapih}}

===Functions===
{{UGapi|a|a}}

{{UGapi|int InputCount() [get] : Constant <nowiki>=</nowiki> 8
|Returns the number of digital inputs supported by this PhidgetInterfaceKit.
}}

{{UGapi|bool InputState(int InputIndex) [get]
|Returns the state of a particular digital input. Digital inputs read True where they are activated and false when they are in their default state.
}}

{{UGapi|int OutputCount() [get] : Constant <nowiki>=</nowiki> 8
|Returns the number of digital outputs supported by this PhidgetInterfaceKit.
}}

{{UGapi|bool OutputState (int OutputIndex) [get,set]
|Sets/returns the state of a digital output. Setting this to true will activate the output, False is the default state. Reading the OutputState immediately after setting it will not return the value set - it will return the last state reported by the Phidget.
}}

{{UGapi|int SensorCount() [get] : Constant <nowiki>=</nowiki> 8
|Returns the number of sensors (Analog Inputs) supported by this PhidgetInterfaceKit. Note that there is no way of determining is a sensor is attached, and what sensor is attached.
}}

{{UGapi|int SensorValue(int SensorIndex) [get]
|Returns the sensed value of a particular Analog Input. SensorValue varies between 0-1000, corresponding to the 0-5V input range of the Analog Input. If you are using an Analog Sensor from Phidgets Inc., it’s manual will specify the formula used to convert SensorValue into the measured property.
}}

{{UGapi|int SensorRawValue (int SensorIndex) [get]
|Returns the full resolution of the Analog Input. This is a more accurate version of SensorValue. The valid range is 0-4095. Note however that the analog outputs on the Interface Kit 8/8/8 are only 10-bit values and this value represents an oversampling to 12-bit.
}}

{{UGapi|double SensorChangeTrigger (int SensorIndex) [get,set]
|Returns the change trigger for an analog input. This is the amount that an inputs must change between successive SensorChangeEvents. This is based on the 0-1000 range provided by getSensorValue. This value is by default set to 10 for most Interface Kits with analog inputs. SensorChangeTrigger is sometimes referred to as sensitivity.
}}

{{UGapi|int DataRate (int SensorIndex) [get,set]
|Gets/sets the data rate for an analog input. This is corresponds to the fastest rate at which SensorChange events will be fired. The data rate is superseded by SensorChangeTrigger, which can be set to 0 if a constant data rate is required. Data Rate is in milliseconds and corresponds to the amount of time between events. Data Rate is bounded by DataRateMax and DataRateMin. The analog inputs cannot all be set to the fastest data rate at the same time - if this is attempted, an exception will be thrown when the data bandwidth has been exceeded. For data rates less then the maximum, data is still sampled at the maximum speed, and averaged between events for the user. Supported data rates are: 1, 2, 4, 8, and every multiple of 8 until DataRateMin. Setting an unsupported data rate (ie. 3, 9, 17) will result in a thrown exception. Note that data rate is limited to 16ms when opening over the Phidget Webservice.
}}

{{UGapi|int DataRateMax (int SensorIndex) [get]
|The maximum data rate that can be set for an analog input, in milliseconds.
}}

{{UGapi|int DataRateMin (int SensorIndex) [get]
|The minimum data rate that can be set for an analog input, in milliseconds. This is usually 1000.
}}

{{UGapi|bool Ratiometric() [get,set]
|Sets/returns the state of Ratiometric. Ratiometric <nowiki>=</nowiki> true configures the Analog Inputs to measure with respect to VCC (nominal 5V). Ratiometric <nowiki>=</nowiki> false configures the Analog Inputs to measure with respect to an internal precision 5V reference. Ratiometric is not updated from the Phidget. It is recommended to explicitly set Ratiometric when the Interfacekit is opened. After changing the ratiometric state, wait until the ratiometric property matches what was set before reading analog data.
}}
===Events===
{{UGapi| | }}

{{UGapi|OnInputChange(int InputIndex, bool State) [event]
|An event that is issued when the state of a digital input changes.
}}

{{UGapi|OnOutputChange(int OutputIndex, bool State), [event]
|An event that is issued when the state of a digital output changes.
}}

{{UGapi|OnSensorChange(int SensorIndex, int SensorValue), [event]
|An event that is issued when the returned value from a sensor (Analog Input) varies by more than the SensorChangeTrigger property.
}}

==Product History==
{{UGhist}}
{{UGrow|April 2011|0|902|Product Release}}

1010 User Guide - Revision history

Mparadis at 14:26, 9 May 2018

Mparadis: /* Product History */

Mparadis: /* Product History */

Burley: /* Getting Started */

Mparadis: /* Technical Details */

Mparadis: /* API */

Burley at 15:07, 10 August 2012

Mparadis at 15:38, 26 July 2012

Mparadis: Created page with "==Getting Started== In order to use the 1010, you must be comfortable with designing your own circuit. You will need to understand the “signals” coming from and going to..."