TMP1100 User Guide - Revision history

Mparadis at 18:20, 1 June 2023

2023-06-01T18:20:53Z

← Older revision		Revision as of 18:20, 1 June 2023
Line 53:		Line 53:
	An important thing to note is that the ambient temperature sensor measures the temperature of the board and the air around it, though not specifically at the junction. Generally you can assume the two locations are nearly the same temperature, however as the electronics heat up by being powered on, there can be some small error introduced. This is exacerbated by having the board in an enclosed space where normal airflow is restricted thereby increasing the effect of self-heating. As a result we recommend that the board be left in as open and well ventilated/cooled a place as possible to minimize this error source.		An important thing to note is that the ambient temperature sensor measures the temperature of the board and the air around it, though not specifically at the junction. Generally you can assume the two locations are nearly the same temperature, however as the electronics heat up by being powered on, there can be some small error introduced. This is exacerbated by having the board in an enclosed space where normal airflow is restricted thereby increasing the effect of self-heating. As a result we recommend that the board be left in as open and well ventilated/cooled a place as possible to minimize this error source.

	For more information on thermocouples, check out the [[Thermocouple ~~Primer~~]].		For more information on thermocouples, check out the [[Thermocouple Guide]].
	}}		}}

	{{UGC-End}}		{{UGC-End}}

Mparadis at 21:23, 17 January 2022

2022-01-17T21:23:24Z

← Older revision		Revision as of 21:23, 17 January 2022
Line 47:		Line 47:
	{{UGC-Graphing}}		{{UGC-Graphing}}
	{{UGC-DataInterval}}		{{UGC-DataInterval}}
			{{UGC-Firmware}}
	{{UGC-Entry\|Cold Junction Compensation and Self-heating\|\|		{{UGC-Entry\|Cold Junction Compensation and Self-heating\|\|
	Thermocouples consist of two junctions, one where the thermocouple meets the Phidget and one where the two wires are welded together at the sensing end of the device. In simplified terms, a thermocouple works by detecting the temperature difference between these two junctions. To measure the temperature at the sensing end we need to know the temperature where the thermocouple connects to the Phidget. There is an ambient temperature sensor on the board. The thermocouple reading is automatically calculated using the data from the on board temperature sensor.		Thermocouples consist of two junctions, one where the thermocouple meets the Phidget and one where the two wires are welded together at the sensing end of the device. In simplified terms, a thermocouple works by detecting the temperature difference between these two junctions. To measure the temperature at the sensing end we need to know the temperature where the thermocouple connects to the Phidget. There is an ambient temperature sensor on the board. The thermocouple reading is automatically calculated using the data from the on board temperature sensor.

Mparadis at 21:00, 28 January 2021

2021-01-28T21:00:21Z

@@ Line 4: / Line 4: @@
 [[Category:UserGuide]]
 ==Part 1: Setup==
-{{UGIntro|TMP1100}}
+{{PT1 Deck Sequence}}
 == Part 2: Using Your Phidget ==

Mparadis: /* Part 4: Advanced Topics and Troubleshooting */

2021-01-06T21:28:18Z

Part 4: Advanced Topics and Troubleshooting

← Older revision		Revision as of 21:28, 6 January 2021
Line 62:		Line 62:
	{{UGC-Start}}		{{UGC-Start}}
	{{UGC-Addressing}}		{{UGC-Addressing}}
			{{UGC-Graphing}}
	{{UGC-DataInterval}}		{{UGC-DataInterval}}
	{{UGC-Entry\|Cold Junction Compensation and Self-heating\|\|		{{UGC-Entry\|Cold Junction Compensation and Self-heating\|\|

Mparadis at 21:37, 4 August 2020

2020-08-04T21:37:12Z

← Older revision		Revision as of 21:37, 4 August 2020
Line 1:		Line 1:
	__NOINDEX__		__NOINDEX__
			__NOTOC__
	<metadesc>Connect one K, J, E or T type thermocouple to the Isolated Thermocouple Phidget to measure the temperature of the air, an object, or a liquid.</metadesc>		<metadesc>Connect one K, J, E or T type thermocouple to the Isolated Thermocouple Phidget to measure the temperature of the air, an object, or a liquid.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==~~Getting Started~~==		==Part 1: Setup==
	{{UGIntro\|TMP1100}}		{{UGIntro\|TMP1100}}
	* [{{SERVER}}/products.php?product_id=TMP1100 TMP1100 - Isolated Thermocouple Phidget]		* [{{SERVER}}/products.php?product_id=TMP1100 TMP1100 - Isolated Thermocouple Phidget]
Line 20:		Line 21:
	{{UGIntroDone\|TMP1100}}		{{UGIntroDone\|TMP1100}}

	~~==Using the TMP1100==~~
	{{UGcontrolpanel\|TMP1100}}		{{UGcontrolpanel\|TMP1100}}

	~~{{ugTemperatureSensorIC\|TMP1100\|, labelled ''Temperature Sensor (IC)'',\|(IC)}}~~		== Part 2: Using Your Phidget ==

	~~{{ugTemperatureSensorThermocouple\|~~TMP1100}}		===About===
			The TMP1100 with an attached thermocouple allows you to measure extreme temperatures. This Phidget connects to a J, K, E, or T type thermocouple. Choose the thermocouple type in software and data will be converted to degrees Celsius automatically. If you have other thermocouple types, you can open the channel in VoltageInput mode and convert it to Celsius manually.

	~~{{ugVoltageInput\|TMP1100\|}}~~		===Explore Your Phidget Channels Using The Control Panel===

	~~{{ugAddressingInformation}}~~		You can use your Control Panel to explore your Phidget's channels.

	~~{{ugUsingYourOwnProgram\|TMP1100}}~~		'''1.''' Open your Control Panel, and you will find the following channels:

	=~~=Technical Details==~~		[[Image:TMP1100_Panel.jpg\|link=\|center]]
	~~{{Coldjunctioncomp}}~~

	~~===Current Consumption===~~		'''2.''' Double click on a channel to open an example program. Each channel belongs to a different channel class:
	~~A graph of the TMP1100~~'~~s current consumption can be viewed below:~~
	~~[[Image~~:~~TMP1100current.jpg\|link=\|700px\|center]]~~

			{{UGC-Start}}

	~~At the shortest data interval~~ (~~20ms~~)~~, it consumes around 17mA of current. At longer intervals, it dips to around 14mA. When~~ the ~~device is unconfigured or closed~~, ~~it consumes approximately 4mA of current. Closing the object and reopening it can provide significant power savings for applications where the temperature only needs to be measured occasionally.~~		{{UGC-Entry\|Temperature Sensor (IC):\| Measures the ambient temperature\|
			In your Control Panel, double click on "Temperature Sensor (IC)":

			[[Image:TMP1100-TemperatureSensorIC.jpg\|center\|link=]]}}

			{{UGC-Entry\|Thermocouple Input:\| Reports the probe temperature\|
			In your Control Panel, double click on "Thermocouple Input":

			[[Image:TMP1100-TemperatureSensorTC.jpg\|center\|link=]]}}

			{{UGC-Entry\|Voltage Input:\| Measures the raw probe voltage\|
			In your Control Panel, double click on "Voltage Input":

			[[Image:TMP1100-VoltageInput.jpg\|center\|link=]]}}

			{{UGC-End}}

			{{UG-Part3}}

			== Part 4: Advanced Topics and Troubleshooting ==
			{{UGC-Start}}
			{{UGC-Addressing}}
			{{UGC-DataInterval}}
			{{UGC-Entry\|Cold Junction Compensation and Self-heating\|\|
			Thermocouples consist of two junctions, one where the thermocouple meets the Phidget and one where the two wires are welded together at the sensing end of the device. In simplified terms, a thermocouple works by detecting the temperature difference between these two junctions. To measure the temperature at the sensing end we need to know the temperature where the thermocouple connects to the Phidget. There is an ambient temperature sensor on the board. The thermocouple reading is automatically calculated using the data from the on board temperature sensor.

			An important thing to note is that the ambient temperature sensor measures the temperature of the board and the air around it, though not specifically at the junction. Generally you can assume the two locations are nearly the same temperature, however as the electronics heat up by being powered on, there can be some small error introduced. This is exacerbated by having the board in an enclosed space where normal airflow is restricted thereby increasing the effect of self-heating. As a result we recommend that the board be left in as open and well ventilated/cooled a place as possible to minimize this error source.

	~~===Channel Configuration===~~
	~~{\| class="wikitable" style="text-align: center"~~
	~~!colspan="6"\|Temperature Object~~
	\|-
	~~!Channel 0~~
	~~\|Thermocouple Input 0~~
	\|-
	~~!Channel 1~~
	~~\|Ambient Temperature~~
	\|}
	~~{\| class="wikitable"~~
	~~!colspan="6"\|Voltage Object~~
	\|-
	~~!Channel 0~~
	~~\|Voltage Input 0~~
	\|}
	For more information on thermocouples, check out the [[Thermocouple Primer]].		For more information on thermocouples, check out the [[Thermocouple Primer]].
			}}

	{{~~UGnext\|~~}}		{{UGC-End}}

Jdecoux at 16:35, 17 October 2019

2019-10-17T16:35:49Z

← Older revision		Revision as of 16:35, 17 October 2019
Line 31:		Line 31:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\|~~This Phidget is compatible with the {{ExampleLink\|TemperatureSensor}} and the {{ExampleLink\|VoltageInput}}.~~}}		{{ugUsingYourOwnProgram\|TMP1100}}

	==Technical Details==		==Technical Details==

Jdecoux: /* Using Your Own Program */

2018-08-28T17:13:01Z

Using Your Own Program

← Older revision		Revision as of 17:13, 28 August 2018
Line 31:		Line 31:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	~~===Using Your Own Program===~~		{{ugUsingYourOwnProgram\|This Phidget is compatible with the {{ExampleLink\|TemperatureSensor}} and the {{ExampleLink\|VoltageInput}}.}}

	~~You are now ready to start writing your own code for the device. The best way to do that is to start from our examples:~~

	This Phidget is compatible with the {{ExampleLink\|TemperatureSensor}} and the {{ExampleLink\|VoltageInput}}.

	Once you have your example, you will need to follow the instructions on the page for your programming language to get it running. To find these instructions, select your programming language from the [[Software_Overview#Language_Support\|Software Overview]] page.

	==Technical Details==		==Technical Details==

Jdecoux at 19:59, 27 August 2018

2018-08-27T19:59:54Z

← Older revision		Revision as of 19:59, 27 August 2018
Line 28:		Line 28:

	{{ugVoltageInput\|TMP1100\|}}		{{ugVoltageInput\|TMP1100\|}}

			{{ugAddressingInformation}}

			===Using Your Own Program===

			You are now ready to start writing your own code for the device. The best way to do that is to start from our examples:

			This Phidget is compatible with the {{ExampleLink\|TemperatureSensor}} and the {{ExampleLink\|VoltageInput}}.

			Once you have your example, you will need to follow the instructions on the page for your programming language to get it running. To find these instructions, select your programming language from the [[Software_Overview#Language_Support\|Software Overview]] page.

	==Technical Details==		==Technical Details==

Mparadis at 16:07, 7 June 2018

2018-06-07T16:07:06Z

← Older revision		Revision as of 16:07, 7 June 2018
Line 6:		Line 6:
	* [{{SERVER}}/products.php?product_id=TMP1100 TMP1100 - Isolated Thermocouple Phidget]		* [{{SERVER}}/products.php?product_id=TMP1100 TMP1100 - Isolated Thermocouple Phidget]
	* {{VINTHub}}		* {{VINTHub}}
	* [{{~~SERVER~~}}~~/?view=comparetable&rel=Phidget%20Cables Phidget cable]~~		* {{CT\|PhidgetCable\|Phidget cable}}
	* USB cable and computer		* USB cable and computer
	* [{{~~SERVER~~}}~~/?view=comparetable&rel=Thermocouples thermocouple]~~		* {{CT\|TC\|Thermocouple}}

Mparadis at 20:22, 8 May 2018

2018-05-08T20:22:27Z

← Older revision		Revision as of 20:22, 8 May 2018
Line 1:		Line 1:
			__NOINDEX__
	<metadesc>Connect one K, J, E or T type thermocouple to the Isolated Thermocouple Phidget to measure the temperature of the air, an object, or a liquid.</metadesc>		<metadesc>Connect one K, J, E or T type thermocouple to the Isolated Thermocouple Phidget to measure the temperature of the air, an object, or a liquid.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]