RCC0004 User Guide - Revision history

Mparadis at 16:28, 1 June 2023

2023-06-01T16:28:32Z

Mparadis: /* General */

2020-01-29T17:30:10Z

General

Jdecoux at 16:45, 17 October 2019

2019-10-17T16:45:54Z

Mparadis: Created page with "NOINDEX Control the postion and speed of up to 8 RC servo motors or actuators with the PhidgetAdvancedServo 8-Motor. Connects to your computer via USB.
2019-09-04T15:19:43Z

Created page with "NOINDEX <metadesc>Control the postion and speed of up to 8 RC servo motors or actuators with the PhidgetAdvancedServo 8-Motor. Connects to your computer via USB.</metadesc..."

New page
NOINDEX
<metadesc>Control the postion and speed of up to 8 RC servo motors or actuators with the PhidgetAdvancedServo 8-Motor. Connects to your computer via USB.</metadesc>
[[Category:UserGuide]]
==Getting Started==
{{UGIntro|RCC0004}}
[{{SERVER}}/products.php?product_id=RCC0004 RCC0004 - PhidgetAdvancedServo 8-Motor]
USB cable and computer
{{CT|PowerSupply|power supply}}
{{CT|Servo|servo motor}}

Next, you will need to connect the pieces:
[[Image:RCC0004_0_Connecting_The_Hardware.jpg|500px|right|link=]]
# Connect the RC servo motors to the Phidget.
# Plug in a power supply using the barrel connector.
# Alternatively, you can connect a power supply into the terminal block. Be sure to observe correct polarity.
# Connect the Phidget to your computer using the USB cable.

<br clear="all">
{{UGIntroDone|RCC0004}}

==Using the RCC0004==
{{UGcontrolpanel|RCC0004}}

{{ugServo|RCC0004|Servo Motor Controller}}

{{ugAddressingInformation}}

{{ugUsingYourOwnProgram|This Phidget is compatible with the {{ExampleLink|RCServo}}.}}

==Technical Details==
===General===
An RC servo motor can be instructed to move to a desired position by the controller. Internally, it monitors the current position, and drives the motor as fast as it can until it reaches the desired position.
This is a very cheap and simple way to control a motor. It has some limitations though - there is no way for the controller to know the current position and speed of the motor. Applications that want smooth movement suffer from the aggressive acceleration.

The RCC0004 is able to address some of these limitations. Instead of sending the desired position immediately, the RCC0004 sends a series of progressive positions according to acceleration and velocity parameters. In most applications, this dramatically smooths the operation of the servo, and allows reasonably precise control of position, velocity and acceleration. The RCC0004 has a built in switching regulator - this allows it to efficiently operate from a wide voltage range (6-15VDC), and maintain proper power to the servo motors even if the power supply is varying. This built in voltage regulator will not operate if your power supply is undersized.

For more information about servo motors and controllers, check out the [[Servo Motor and Controller Primer]].

===Limitations===
The RCC0004 does not know the current position of the motor on its own. If your motor is free to
move, and is not being driven beyond the physical limitations of the motor, the position returned to your application will be very close to the position of the motor.

===Using the RCC0004 with Continuous Rotation Servos===
A continuous rotation servo is a servo motor that has had its headgear-stop removed and potentiometer replaced by two matched-value resistors. This has the effect of allowing the motor to rotate freely through a full range of motion, but disables the motor’s ability to control it’s position.

When using the RCC0004 with a servo motor modified in this way, the position control in software becomes the motor’s speed control. Because the two resistors that replace the motor’s potentiometer are matched in value, the motor will always think its shaft is at center position. If the target position in software is set to center, the motor will believe it has achieved the target and will therefore not rotate. The further away from center the target position is set to, the faster the motor will rotate (trying to reach that position, but never doing so). Changing the value above or below center changes the direction of rotation.

===Using the RCC0004 with Electronic Speed Controllers (ESCs)===
Electronic Speed Controllers are commonly used in RC hobby planes, cars, helicopters. It’s a controller that accepts a PWM input signal, and controls a motor based on that signal. The ESC accepts power from an external source, normally a battery pack.

ESCs can be controlled by the RCC0004, but the vast majority of ESCs on the market will destroy the RCC0004 if they are plugged in without modification. In a hobby RC system, the ESC is responsible for regulating some of the battery current down to ~5V, and supplying it to the radio receiver. An ESC designed to the power the receiver will advertise that it has a Battery Eliminator Circuit (BEC). When you plug an ESC into the RCC0004, the RCC0004 is acting as the radio receiver. The RCC0004 was not designed to be powered by the devices it controls, and the voltage regulator on the RCC0004 will self-destruct if a device tries to power it. If the center pin from the 3-wire servo connector between the RCC0004 and the ESC is disconnected, the BEC on the ESC will not be able to power the RCC0004, and the voltage regulator will not fail.

How the ESC inteprets the PWM signal and controls the motor is a function of the ESC. Higher end ESCs can be configured based on the application.

The hobby RC market has transitioned to Brushless DC Motors (BLDC). As you select an ESC, watch that the battery voltage input matches that of your system, and the type of motor controlled is what you have. Brushed DC and Brushless DC Motors are completely different, and require different controllers.

Wiring layout is critical with ESCs. The currents to the motor and on the ground return can be enormous. If these currents end up travelling back through USB cables, the system will not be stable. Some ESCs are optically isolated (OPTO) - a big advantage that reduces interference.

===Synchronization of Multiple Servo Motors===
Many applications call for several servo motors operating in unison - for example, operating a CNC table, or a robot arm. Highly precise synchronization of multiple servos using the RCC0004 is not possible, as the sequencing will be affected by the real-time performance of your operating system. Each servo is controlled as a independent unit, so there is no way of arranging for a particular action to happen to all motors at the same time. Typical jitter can be 10-30ms.

===Connecting your Servo Motor to the RCC0004===
[[File:RCC0004_0_Pins.jpg|center|500px|link=]]

The pins on the RCC0004 are labelled W R B on the board:

* W (White or Yellow depending on your servo motor) is the Data Line
* B (Black) is the Ground
* R (Red) is 5V

If you need to use a servo motor with a higher power requirement than the RCC0004 can provide, you can cut the red and black wires on the Phidget cable and solder them to the power and ground of an external power supply. If you do this, make sure you disconnect the red wire from the RCC0004, because reverse current from the external power supply could damage the servo controller board.

{{UGnext|}}