OUT1002 User Guide - Revision history

Mparadis: /* Part 4: Advanced Topics and Troubleshooting */

2026-03-04T18:46:05Z

Part 4: Advanced Topics and Troubleshooting

@@ Line 42: / Line 42: @@
 {{UGC-Addressing}}
 {{UGC-Firmware}}
 {{UGC-Entry|Current Sourcing and Sinking|
+|

Mparadis: /* About */

2026-03-04T17:15:01Z

About

← Older revision		Revision as of 17:15, 4 March 2026
Line 14:		Line 14:
	[[Image:OUT1002_About.jpg\|link=\|800px]]		[[Image:OUT1002_About.jpg\|link=\|800px]]

	'''Note:''' The two terminals cannot be controlled separately. You must select a single mode by setting the '''VoltageOutputRange''' in software, and only use the terminals for that mode. Because of this, the 5V terminal will produce 2.5V ~~even~~ when the channel is ~~closed~~. See advanced topics below for more information.		'''Note:''' The two terminals cannot be controlled separately. You must select a single mode by setting the '''VoltageOutputRange''' in software, and only use the terminals for that mode. Because of this, the 5V terminal will produce 2.5V when the channel is not open. See advanced topics below for more information.

	===Explore Your Phidget Channels Using The Control Panel===		===Explore Your Phidget Channels Using The Control Panel===

Mparadis: /* About */

2026-03-04T17:14:03Z

About

← Older revision		Revision as of 17:14, 4 March 2026
Line 14:		Line 14:
	[[Image:OUT1002_About.jpg\|link=\|800px]]		[[Image:OUT1002_About.jpg\|link=\|800px]]

	'''Note:''' The two terminals cannot be controlled separately. You must select a single mode by setting the '''VoltageOutputRange''' in software, and only use the terminals for that mode.		'''Note:''' The two terminals cannot be controlled separately. You must select a single mode by setting the '''VoltageOutputRange''' in software, and only use the terminals for that mode. Because of this, the 5V terminal will produce 2.5V even when the channel is closed. See advanced topics below for more information.

	===Explore Your Phidget Channels Using The Control Panel===		===Explore Your Phidget Channels Using The Control Panel===

Mparadis at 21:18, 17 January 2022

2022-01-17T21:18:33Z

← Older revision		Revision as of 21:18, 17 January 2022
Line 41:		Line 41:
	{{UGC-Start}}		{{UGC-Start}}
	{{UGC-Addressing}}		{{UGC-Addressing}}
			{{UGC-Firmware}}
	{{UGC-Entry\|Current Sourcing and Sinking\|		{{UGC-Entry\|Current Sourcing and Sinking\|
	\|		\|

Mparadis: /* Explore Your Phidget Channels Using The Control Panel */

2021-03-17T16:55:57Z

Explore Your Phidget Channels Using The Control Panel

← Older revision		Revision as of 16:55, 17 March 2021
Line 28:		Line 28:
	{{UGC-Start}}		{{UGC-Start}}

	{{UGC-Entry\|Voltage Output: \| Produce a DC voltage for the connected circuit or device		{{UGC-Entry\|Isolated 16-Bit Voltage Output Phidget: \| Produce a DC voltage for the connected circuit or device
	\|		\|
	In your Control Panel, double click on "Isolated 16-Bit Voltage Output Phidget":		In your Control Panel, double click on "Isolated 16-Bit Voltage Output Phidget":

	[[Image:OUT1002-VoltageOutput.jpg\|center~~\|850px~~\|link=]]}}		[[Image:OUT1002-VoltageOutput.jpg\|center\|link=]]}}

	{{UGC-End}}		{{UGC-End}}

Mparadis: /* About */

2021-03-09T21:18:11Z

About

← Older revision		Revision as of 21:18, 9 March 2021
Line 12:		Line 12:
	This Phidget is ideal for analog voltage-controlled devices.		This Phidget is ideal for analog voltage-controlled devices.

	'''Note:''' The two terminals cannot be controlled separately.		[[Image:OUT1002_About.jpg\|link=\|800px]]

			'''Note:''' The two terminals cannot be controlled separately. You must select a single mode by setting the '''VoltageOutputRange''' in software, and only use the terminals for that mode.

	===Explore Your Phidget Channels Using The Control Panel===		===Explore Your Phidget Channels Using The Control Panel===

Mparadis at 20:33, 28 January 2021

2021-01-28T20:33:16Z

@@ Line 4: / Line 4: @@
 [[Category:UserGuide]]
 ==Part 1: Setup==
-{{UGIntro|OUT1002}}
+{{PT1 Deck Sequence}}
 == Part 2: Using Your Phidget ==

Mparadis at 20:08, 27 May 2020

2020-05-27T20:08:33Z

← Older revision		Revision as of 20:08, 27 May 2020
Line 1:		Line 1:
	__NOINDEX__		__NOINDEX__
			__NOTOC__
	<metadesc>Produce a voltage from -10 to +10 volts with the Isolated 16-Bit Voltage Output Phidget. Connects to a port on your VINT Hub.</metadesc>		<metadesc>Produce a voltage from -10 to +10 volts with the Isolated 16-Bit Voltage Output Phidget. Connects to a port on your VINT Hub.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==~~Getting Started~~==		==Part 1: Setup==
	{{UGIntro\|OUT1002}}		{{UGIntro\|OUT1002}}
	*[{{SERVER}}/products.php?product_id=OUT1002 OUT1002 - Isolated 16-bit Voltage Output Phidget]		*[{{SERVER}}/products.php?product_id=OUT1002 OUT1002 - Isolated 16-bit Voltage Output Phidget]
Line 19:		Line 20:
	{{UGIntroDone\|OUT1002}}		{{UGIntroDone\|OUT1002}}

	~~==Using the OUT1002==~~
	{{UGcontrolpanel\|OUT1002}}		{{UGcontrolpanel\|OUT1002}}

	~~{{ugVoltageOutput\|OUT1002\|, labelled ''Isolated 16-bit Voltage Output~~ Phidget~~'', }}~~		== Part 2: Using Your Phidget ==
	*Select the ''Voltage Output Range'' from the drop-down menu. You can choose between 0-5V output or ±10V output.

	~~{{ugAddressingInformation}}~~		===About===
			The OUT1002 can provide a DC voltage between -10V and +10V on the 10V terminal. The 5V terminal provides a voltage between 0V to 5V. The 5V terminal has a higher resolution than the 10V terminal.
			This Phidget is ideal for analog voltage-controlled devices.

	~~{{ugUsingYourOwnProgram\|OUT1002}}~~		'''Note:''' The two terminals cannot be controlled separately.

	~~==Technical Details==~~		===Explore Your Phidget Channels Using The Control Panel===
	===Control ~~Application~~===
	~~[[Image:OUT1002_Control_Diagram.jpg\|link=\|350px\|right]]~~
	~~Some devices may require an analog voltage as a control input. The OUT1002 supplies a fixed voltage up to ±10V, which can be used to control such devices.~~

	~~In addition~~, ~~this device is isolated~~ and ~~can apply its~~ voltage ~~anywhere in an application~~ circuit, ~~independent of USB ground~~.		You can use your Control Panel to explore your Phidget's channels.
	~~<br clear="all">~~
			'''1.''' Open your Control Panel, and you will find the '''Isolated 16-Bit Voltage Output Phidget''' channel:

			[[Image:OUT1002_Panel.jpg\|link=\|center]]

			'''2.''' Double click on the channel to open an example program. This channel belongs to the '''Voltage Output''' channel class:

			{{UGC-Start}}

			{{UGC-Entry\|Voltage Output: \| Produce a DC voltage for the connected circuit or device
			\|
			In your Control Panel, double click on "Isolated 16-Bit Voltage Output Phidget":

			[[Image:OUT1002-VoltageOutput.jpg\|center\|850px\|link=]]}}

			{{UGC-End}}

	~~===Transient Voltages===~~		{{UG-Part3}}
	The OUT1002 may have an unpredictable output voltage for a very short time immediately after the device changes modes, or is turned on. If this is a problem in your application and you have no way to ignore it via software, we recommend using a [[Solid State Relay Primer\|solid state relay]] to switch the output on once it has stabilized.

	===Current Sourcing and Sinking~~===~~		== Part 4: Advanced Topics and Troubleshooting ==
			{{UGC-Start}}
			{{UGC-Addressing}}
			{{UGC-Entry\|Current Sourcing and Sinking\|
			\|
	To ensure maximum voltage precision across the device's full range, the OUT1002 Phidget should be subjected to a minimal current draw, ideally less than 5mA in ±10V mode. 5V mode should only be used to set a voltage in high-impedance applications.		To ensure maximum voltage precision across the device's full range, the OUT1002 Phidget should be subjected to a minimal current draw, ideally less than 5mA in ±10V mode. 5V mode should only be used to set a voltage in high-impedance applications.
			However, in the event you plan to power a small load with this device, it will either be sourcing or sinking current when in use. When it's connected to a circuit with a lower voltage potential than its own voltage setting, the current will be flowing out from the OUT1002 into the circuit, so it will be sourcing current. When it's connected to a circuit with a higher voltage potential than the voltage it's set to, the current will flow from the circuit into the OUT1002 for a current sinking situation.
	However, in the event you plan to power a small load with this device, it will either be sourcing or sinking current when in use. When it's connected to a circuit with a lower voltage potential than its own voltage setting, current will be flowing out from the OUT1002 into the circuit, so it will be sourcing current. When it's connected to a circuit with a higher voltage potential than the voltage it's set to, current will flow from the circuit into the OUT1002 for a current sinking situation.
	[[Image:sourcesink_diagram.jpg\|link=\|600px\|center]]		[[Image:sourcesink_diagram.jpg\|link=\|600px\|center]]

			The OUT1002 can source or sink up to 26mA of current depending on the selected output voltage and mode. Please refer to the chart below to determine the amount of current that can be sourced or sunk.

	~~The OUT1002 can source or sink up to 26mA of current depending on the selected output voltage and mode. Please refer to the chart below to determine the amount of current that can be sourced or sunk.~~
	[[Image:sourcesink1002_5v.jpg\|link=\|650px\|center]]		[[Image:sourcesink1002_5v.jpg\|link=\|650px\|center]]


	[[Image:sourcesink1002_10v.jpg\|link=\|650px\|center]]		[[Image:sourcesink1002_10v.jpg\|link=\|650px\|center]]


	For example, if the connected circuit is pulling 25mA of current, the OUT1002 will only be able to provide a maximum of 2V (in 0-5V mode), even if you try to set it to a higher value.		For example, if the connected circuit is pulling 25mA of current, the OUT1002 will only be able to provide a maximum of 2V (in 0-5V mode), even if you try to set it to a higher value.

			}}

	{{~~UGnext\|~~}}		{{UGC-End}}

Jdecoux at 16:33, 17 October 2019

2019-10-17T16:33:13Z

← Older revision		Revision as of 16:33, 17 October 2019
Line 27:		Line 27:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\|~~This Phidget is compatible with the {{ExampleLink\|VoltageOutput}}.~~}}		{{ugUsingYourOwnProgram\|OUT1002}}

	==Technical Details==		==Technical Details==

Jdecoux: /* Using Your Own Program */

2018-08-28T17:02:32Z

Using Your Own Program

← Older revision		Revision as of 17:02, 28 August 2018
Line 27:		Line 27:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	~~===Using Your Own Program===~~		{{ugUsingYourOwnProgram\|This Phidget is compatible with the {{ExampleLink\|VoltageOutput}}.}}

	~~You are now ready to start writing your own code for the device. The best way to do that is to start from our examples:~~

	This Phidget is compatible with the {{ExampleLink\|VoltageOutput}}.

	Once you have your example, you will need to follow the instructions on the page for your programming language to get it running. To find these instructions, select your programming language from the [[Software_Overview#Language_Support\|Software Overview]] page.

	==Technical Details==		==Technical Details==