1139 User Guide - Revision history

Mparadis: /* Formulas */

2018-05-10T20:52:36Z

Formulas

← Older revision		Revision as of 20:52, 10 May 2018
Line 33:		Line 33:

	===Formulas===		===Formulas===
	{{UGSensorFormula\|pressure (kPa)}} The Formula to translate voltage into Pressure is:		{{UGSensorFormula\|pressure (kPa)}} The Formula to translate voltage ratio into Pressure is:


	:<math>		:<math>
	\text{Pressure (kPa)}= \frac{\text{~~Voltage~~} \times ~~200~~}{9} - 4.444		\text{Pressure (kPa)}= \frac{\text{VoltageRatio} \times 1000}{9} - 4.444
	</math>		</math>

Line 43:		Line 43:

	:<math>		:<math>
	\text{Pressure (psi)} = (\text{~~Voltage~~} \times 3.~~222~~) - 0.6444		\text{Pressure (psi)} = (\text{VoltageRatio} \times 16.11) - 0.6444
	</math>		</math>

Mparadis at 20:39, 8 May 2018

2018-05-08T20:39:10Z

← Older revision		Revision as of 20:39, 8 May 2018
Line 1:		Line 1:
			__NOINDEX__
	<metadesc>The Phidget Differential Air Pressure Sensor plugs into an Analog Input or VINT Hub port and measures pressure from 0 kPa to 100 kPa.</metadesc>		<metadesc>The Phidget Differential Air Pressure Sensor plugs into an Analog Input or VINT Hub port and measures pressure from 0 kPa to 100 kPa.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]

Jdecoux at 19:11, 11 April 2018

2018-04-11T19:11:51Z

← Older revision		Revision as of 19:11, 11 April 2018
Line 6:		Line 6:

	Next, you will need to connect the pieces:		Next, you will need to connect the pieces:
	[[Image:~~1136_0_Connecting_The_Hardware~~.jpg\|400px\|right\|link=]]		[[Image:1139_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the 1139 to the HUB0000 with the Phidget cable.		# Connect the 1139 to the HUB0000 with the Phidget cable.
	# Connect the HUB0000 to your computer with the USB cable.		# Connect the HUB0000 to your computer with the USB cable.

Jdecoux at 19:11, 11 April 2018

2018-04-11T19:11:37Z

← Older revision		Revision as of 19:11, 11 April 2018
Line 7:		Line 7:
	Next, you will need to connect the pieces:		Next, you will need to connect the pieces:
	[[Image:1136_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]		[[Image:1136_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the 1139 to the ~~1018~~ with the Phidget cable.		# Connect the 1139 to the HUB0000 with the Phidget cable.
	# Connect the ~~1018~~ to your computer with the USB cable.		# Connect the HUB0000 to your computer with the USB cable.

	<br clear="all">		<br clear="all">
Line 14:		Line 14:

	==Using the 1139==		==Using the 1139==
	{{UGcontrolpanelSensor\|1139\|~~1018~~}}		{{UGcontrolpanelSensor\|1139\|HUB0000}}

	{{UGSensorVoltageRatioInput\|1139\|pressure (kPa)}}		{{UGSensorVoltageRatioInput\|1139\|pressure (kPa)}}

Mparadis at 16:32, 29 November 2017

2017-11-29T16:32:59Z

← Older revision		Revision as of 16:32, 29 November 2017
Line 1:		Line 1:
			<metadesc>The Phidget Differential Air Pressure Sensor plugs into an Analog Input or VINT Hub port and measures pressure from 0 kPa to 100 kPa.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==Getting Started==		==Getting Started==

Lmpacent at 22:42, 16 June 2017

2017-06-16T22:42:10Z

← Older revision		Revision as of 22:42, 16 June 2017
Line 1:		Line 1:
	[[Category:UserGuide]]		[[Category:UserGuide]]
			==Getting Started==
			{{UgSensorIntro\|1139\|Differential Air Pressure Sensor 100 kPa\|Voltage Ratio Input port}}

	~~===Required Hardware===~~

	* A [{{SERVER}}/products.php?product_id=1139 1139 Gas Pressure Sensor]		Next, you will need to connect the pieces:
	* An InterfaceKit or Hub to ~~read~~ the ~~sensor~~
	* A Phidget cable
	* A USB cable
	* A computer

	~~===Connecting the Pieces===~~
	[[Image:1136_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]		[[Image:1136_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the ~~pressure sensor~~ to the ~~InterfaceKit or Hub~~ with the Phidget cable.		# Connect the 1139 to the 1018 with the Phidget cable.
	# Connect the ~~InterfaceKit or Hub~~ to your computer with the USB cable.		# Connect the 1018 to your computer with the USB cable.

	<br clear="all">		<br clear="all">
	==~~Testing~~ Using ~~Windows~~==		{{UGIntroDone\|1139}}

			==Using the 1139==
			{{UGcontrolpanelSensor\|1139\|1018}}

	{{~~UgSensor~~}}		{{UGSensorVoltageRatioInput\|1139\|pressure (kPa)}}

	==Technical Details==		==Technical Details==
			===General===
	The ~~Differential Gas Pressure Sensor~~ uses bipolar processing to provide an accurate, high level analog input signal that is proportional to the applied pressure.		The 1139 uses bipolar processing to provide an accurate, high level analog input signal that is proportional to the applied pressure. When the sensor is plugged in, the sensor voltage should default to about 0.2V, which corresponds to 0 kPa between the two ports.
	When the sensor is plugged in, the sensor voltage should default to about 0.2V, which corresponds to 0 kPa between the two ports.

	===Ports===		===Ports===
Line 31:		Line 28:
	[[File:1138_0_Ports.jpg\|300px\|right\|link=]]		[[File:1138_0_Ports.jpg\|300px\|right\|link=]]

	For hosing, we recommend using polyurethane tubing. We have had good results with 2.4mm ID tubing from ~~Emiplastics~~.com. In imperial measurement, 3/32” ID tubing is equivalent. This is available through laboratory supply stores such as Cole Parmer.		For hosing, we recommend using polyurethane tubing. We have had good results with 2.4mm ID tubing from [http://www.emicorp.com/ EMI]. In imperial measurement, 3/32” ID tubing is equivalent. This is available through laboratory supply stores such as [https://www.coleparmer.com/ Cole Parmer].

	~~<br clear=all>~~

	===Formulas===		===Formulas===
	The Formula to translate voltage into Pressure is:		{{UGSensorFormula\|pressure (kPa)}} The Formula to translate voltage into Pressure is:


Line 49:		Line 44:
	</math>		</math>

			<br clear=all>
	~~'''Note:''' 1.0 kPa~~ = ~~0.145 psi~~

	{{UGasens}}		{{UGasens}}

	{{UGnext\|}}		{{UGnext\|}}

Mparadis at 16:25, 6 June 2017

2017-06-06T16:25:58Z

← Older revision		Revision as of 16:25, 6 June 2017
Line 3:		Line 3:
	===Required Hardware===		===Required Hardware===

	* A 1139 Gas Pressure Sensor		* A [{{SERVER}}/products.php?product_id=1139 1139 Gas Pressure Sensor]
	* An InterfaceKit or Hub to read the sensor		* An InterfaceKit or Hub to read the sensor
	* A Phidget cable		* A Phidget cable

Mparadis: /* Technical Details */

2017-04-18T16:40:56Z

Technical Details

← Older revision		Revision as of 16:40, 18 April 2017
Line 22:		Line 22:

	The Differential Gas Pressure Sensor uses bipolar processing to provide an accurate, high level analog input signal that is proportional to the applied pressure.		The Differential Gas Pressure Sensor uses bipolar processing to provide an accurate, high level analog input signal that is proportional to the applied pressure.
	When the sensor is plugged in, the ~~SensorValue~~ should default to about 40, which corresponds to 0 kPa between the two ports.		When the sensor is plugged in, the sensor voltage should default to about 0.2V, which corresponds to 0 kPa between the two ports.

	===Ports===		===Ports===
Line 36:		Line 36:

	===Formulas===		===Formulas===
	The Formula to translate ~~SensorValue~~ into Pressure is:		The Formula to translate voltage into Pressure is:


	:<math>		:<math>
	\text{Pressure (kPa)}= \frac{\text{~~SensorValue~~}}{9} - 4.444		\text{Pressure (kPa)}= \frac{\text{Voltage} \times 200}{9} - 4.444
	</math>		</math>

Line 46:		Line 46:

	:<math>		:<math>
	\text{Pressure (psi)} = ~~\frac{~~\text{~~SensorValue~~}~~}{62~~.~~07}~~ - 0.6444		\text{Pressure (psi)} = (\text{Voltage} \times 3.222) - 0.6444
	</math>		</math>

Mparadis: /* Technical Details */

2016-11-14T15:53:35Z

Technical Details

← Older revision		Revision as of 15:53, 14 November 2016
Line 51:		Line 51:

	'''Note:''' 1.0 kPa = 0.145 psi		'''Note:''' 1.0 kPa = 0.145 psi

	~~{{UGotherint}}~~

	{{UGasens}}		{{UGasens}}

	{{UGnext\|}}		{{UGnext\|}}

Mparadis at 11:07, 19 October 2016

2016-10-19T11:07:28Z

← Older revision		Revision as of 11:07, 19 October 2016
Line 5:		Line 5:
	* A 1139 Gas Pressure Sensor		* A 1139 Gas Pressure Sensor
	* An InterfaceKit or Hub to read the sensor		* An InterfaceKit or Hub to read the sensor
	* A ~~sensor~~ cable		* A Phidget cable
	* A USB cable		* A USB cable
	* A computer		* A computer
Line 11:		Line 11:
	===Connecting the Pieces===		===Connecting the Pieces===
	[[Image:1136_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]		[[Image:1136_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the pressure sensor to the InterfaceKit or Hub with the ~~sensor~~ cable.		# Connect the pressure sensor to the InterfaceKit or Hub with the Phidget cable.
	# Connect the InterfaceKit or Hub to your computer with the USB cable.		# Connect the InterfaceKit or Hub to your computer with the USB cable.