Products for USB Sensing and Control
This optical rotary encoder sits on the 5mm rear shaft of a motor to track its position and velocity.
This quadrature encoder must be read by an encoder interface. These interfaces will interpret the two quadrature signals in order to determine the continuous position of the rotating part. The following interfaces are compatible with this encoder:
| Product | Encoder Interface | ||
|---|---|---|---|
| Part Number | Price | Number of Encoder Inputs | Count Rate Max |
 Quadrature Encoder Phidget
|
$15.00 | 1 | 1E+06 pulses/s |
 4A DC Motor Phidget
|
$40.00 | 1 | 400000 pulses/s |
 DC Motor Phidget
|
$75.00 | 1 | 400000 pulses/s |
 PhidgetEncoder HighSpeed
|
$50.00 | 1 | 1E+06 pulses/s |
 PhidgetEncoder HighSpeed 4-Input
|
$75.00 | 4 | 1E+06 pulses/s |
 PhidgetEncoder HighSpeed
|
$40.00 | 1 | 2E+06 pulses/s |
 PhidgetEncoder HighSpeed 4-Input
|
$65.00 | 4 | 1E+06 pulses/s |
 PhidgetMotorControl 1-Motor
|
$75.00 | 1 | 500000 cycles/s |
The following BLDC motors have the correct shaft size and mounting pattern to make use of this encoder:
| Product | Physical Properties | Motor Properties | ||
|---|---|---|---|---|
| Part Number | Price | Rear Shaft Diameter | Rated Torque | Rated Speed |
 NEMA17 - Brushless DC Motor - 106:1 Gearbox
|
$85.00 | 5 mm | 96.9 kg·cm | 38 RPM |
 NEMA23 - Brushless DC Motor - 4.3:1 Gearbox
|
$84.00 | 5 mm | 10.2 kg·cm | 930 RPM |
 NEMA23 - Brushless DC Motor - 15:1 Gearbox
|
$86.00 | 5 mm | 33.7 kg·cm | 250 RPM |
Ensure you have all the pieces before you start assembly:
You'll need a small Phillips head or flathead screwdriver for this assembly.
Step 1: Unscrew the encoder cap from the base and separate the pieces.
Step 2: Attach the encoder base to the motor using the two small screws without washers. Make sure the raised edge is facing out so the cap will fit on later.
Step 3: Remove the encoder wheel from the foam packaging and slide it onto the shaft with the flange facing out. Don't tighten the set screws yet.
Step 4: Move the optical reader in, sliding the encoder wheel on the shaft so the wheel is resting within the reader's prongs. There are pegs on the bottom of the reader that line up with holes in the base to make this step easier.
Step 5: Once both parts are in place, use the two small screws with washers to mount the reader. Be careful not to overtighten the screws, or you may damage the plastic clips on the reader.
Step 6: Position the encoder wheel so that it is halfway between the reader's prongs, and then tighten both set screws on the wheel's flange using the included allan key.
Step 7: Place the cap on the encoder, ensuring that the rubber gasket on the encoder cable is seated in between the base and the cap
Step 8: Use the two long screws to attach the encoder cap to the base.
| Encoder Properties | |
|---|---|
| Manufacturer Part Number | MFT3005-E-1000B5-G05 |
| Output Circuit Type | Push-Pull |
| Controlled By | Encoder Interface |
| Encoder Resolution | 1000 CPR |
| Encoder Speed Max | 5000 RPM |
| Electrical Properties | |
| Supply Voltage Min | 5 V DC |
| Supply Voltage Max | 5 V DC |
| Physical Properties | |
| Shaft Diameter | (Inner) 5 mm |
| Hex Key Size Required | 1.5 mm |
| Cable Length | 500 mm |
| Shaft Maximum Axial Load | 15 N |
| Shaft Maximum Radial Load | 25 N |
| Operating Temperature Min | -40 °C |
| Operating Temperature Max | 85 °C |
| Customs Information | |
| Canadian HS Export Code | 9029.10.00 |
| American HTS Import Code | 9029.10.80.00 |
| Country of Origin | CN (China) |
| Product | Encoder Properties | |||
|---|---|---|---|---|
| Part Number | Price | Output Circuit Type | Encoder Resolution | Encoder Speed Max |
 Rotary Encoder - 12mm Hollow Shaft 1000CPR with Index
|
$50.00 | Push-Pull | 1000 CPR | 6000 RPM |
 Rotary Encoder - 12mm Solid Shaft 1000CPR with Index
|
$60.00 | Push-Pull | 1000 CPR | 2000 RPM |
 Rotary Encoder - 6mm Solid Shaft 1000CPR with Index
|
$40.00 | Push-Pull | 1000 CPR | 6000 RPM |
 Rotary Encoder - 6mm Solid Shaft 600CPR
|
$25.00 | Push-Pull | 600 CPR | 6000 RPM |
 Rotary Encoder - 8mm Solid Shaft 1000CPR with Index
|
$45.00 | Push-Pull | 1000 CPR | 6000 RPM |
 Rotary Encoder - For 4mm Motor Shaft 300 CPR
|
$25.00 | Push-Pull | 300 CPR | 6000 RPM |
 Rotary Encoder - For 4mm Motor Shaft 40 CPR
|
$10.00 | Push-Pull | 40 CPR | 6000 RPM |
 Rotary Encoder - For 5mm Motor Shaft 1000CPR
|
$30.00 | Push-Pull | 1000 CPR | 5000 RPM |
 Rotary Encoder with 4mm Shaft (360 CPR)
|
$50.00 | Push-Pull | 360 CPR | 3000 RPM |
 Rotary Encoder with 8mm Bore (500 CPR)
|
$50.00 | Push-Pull | 500 CPR | 4500 RPM |
