VINT Hubs & Devices

The core of our product line, the USB VINT Hub has 6 VINT ports allowing for endless possibilities for USB sensing and control.

Use Phidgets in your local network with this 6 port Wireless VINT Hub. Works with ethernet or a WiFi network.

Single Board Computer running Debian with 3 high-speed USB ports and 6 VINT ports. 512 MiB SDRAM and 16 GB SD Card.

Connect a pH probe or any voltage-based probe that uses a BNC connector to your VINT port with this isolated adapter.

With eight analog ports, you can connect a bunch of 5V sensors or measure small voltage signals.

Add 4 digital inputs to your VINT Hub. These inputs have a shorter trigger time than a VINT port in Digital Input mode.

Add 4 isolated active-high digital inputs to your hub at the cost of only one VINT port.

Add 16 isolated active-high digital inputs to your hub at the cost of only one VINT port.

Reads one 4-20mA, frequency output, PNP/NPN or 5V sensor, and provides 12 or 24V without an external supply.

Measure up to 2 load cells or Wheatstone Bridge-based sensors with this input module. Connects to a VINT port.

Control one high-current brushed DC motor with this powerful Phidget. The encoder input and analog input can enable precise control motor velocity and position.

Control a single DC motor up to 4A with this compact and affordable Phidget. Connects to a VINT port.

Control two DC motors from one VINT port with this compact motor controller.

Control a brushless DC motor from your VINT Hub. The hall effect input enables easy position and velocity control.

Measure distances up to 170mm with this infrared time-of-flight sensor. Connects to a VINT port.

Measure distances up to 650mm with this infrared time-of-flight sensor. Connects to a VINT port.

Measure distances up to 1300mm with this infrared time-of-flight sensor. Connects to a VINT port.

Detect several solid objects up to 10m away in a wide sensing range, or use this Phidget as an ultrasonic range finder.

Interface a quadrature encoder at speeds of up to 100,000 quadrature cycles per second to a port on your VINT Hub.

Use this array of capactive touch buttons as a unique way to control your Phidgets.

Use this capacitive touch wheel and buttons as an intuitive user interface to your Phidgets system.

Make a custom controller for your project with this thumbstick. Two-axis with a center pushbutton, it plugs into a VINT port.

This dial has a fully continuous range of motion and a center pushbutton. Connects to a VINT port.

Measure relative humidity from 0 to 100% and temperature from -40°C to +85°C.

Measure relative humidity from 0 to 100% and temperature from -40°C to +85°C.

Write text and draw pictures to this 128x64px graphic LCD display that connects to a VINT port.

Control the current, voltage and brightness of 32 LEDs from a VINT port with this externally powered module.

This light sensor measures from 188 μlux to 220 klux and connects to any VINT port.

Measure acceleration up to ±8g in each axis with the 3-Axis Accelerometer Phidget. Connects to a VINT port.

An accelerometer, gyroscope, and magnetometer all in one board. Measuring in 3 axes, it plugs right into your VINT hub.

Produce a voltage from 0 to 4.2 volts with this simple voltage output module.

Produce a voltage from -10 to +10 volts with this isolated voltage output module.

Produce a voltage from -10 to +10 volts with this 16-bit isolated voltage output module.

Add four 5V PWM-enabled digital outputs to your hub with this simple and affordable module.

Precisely measure the absolute air pressures between 50 and 110 kPa with this barometer that connects to any VINT port.

This wall socket makes it easy for your VINT Hub to switch power to a device or appliance.

Control position, velocity, and acceleration of 16 RC servos with just one VINT port.

Switch the power of up to four circuits at 210W of DC power or 1750 VA of AC power with this mechanical relay module.

Add four PWM-enabled solid state relay outputs to your hub with this module. This board is isolated to prevent ground loops.

Add 16 PWM-enabled solid state relay outputs to your hub. This module is isolated from input to output.

Protect your circuit and power supply by detecting and preventing overvoltage and overtemperature situations.

Measure sound from 34 to 102 dB (SPL). Supports A and C weightings, and can split data into distinct frequency bands.

Control the position, velocity, and acceleration of one high-power stepper motor with this Phidget.

This compact Stepper Phidget gives you control of one bipolar stepper motor from a port on your VINT hub.

This Phidget connects to a VINT port and measures ambient temperature from -40°C to 85°C quickly and easily.

Connect one K, J, E or T type thermocouple to this Phidget to measure the temperature of the air, an object, or a liquid.

Connect up to four K, J, E or T type thermocouples to this Phidget to measure the temperature of the air or an object.

Measure RTDs, thermistors, and other resistance-based sensors with this VINT port adapter.

Measure up to ±40V with this high precision isolated voltage input Phidget. Connects to a VINT port.

This Phidget measures voltage potentials of up to ±40V. It connects to a VINT port and is isolated for increased reliability.

Measure tiny voltage differences of up to ±1V with precision. This Phidget is isolated and plugs into a VINT port.

Measure in-line DC current flow of up to 30A with this Phidget that connects to a VINT port.

Use a VINT port with this relay to switch power to a circuit running at up to 210 watts DC or 1750 volt-amperes AC.

Switch a small digital signal with this DPDT mechanical relay Phidget. Switch up to 60W of DC power or 125 VA of AC power.

This solid state relay module can switch up to 30V and 10A AC or DC using a port on your VINT Hub.